FS: FKS/Pivot Bindings: Used complete sets, and parts, mix-and-match

[adrian.bee]

Anyone have a heel piece they want to get rid of


Sent from my iPhone using Tapatalk

[jakezee]

Looking for some heel shims to get some Delta Force on my new Brahma 82's - anyone holding?

[phatty]

Anyone have a heel piece they want to get rid of


Sent from my iPhone using Tapatalk

I'll have some heel piece turntables without brake arms. Could probably recycle yours with your brakes/dildos.

[adrian.bee]

I'll have some heel piece turntables without brake arms. Could probably recycle yours with your brakes/dildos.

I love this place.


Sent from my iPhone using Tapatalk

[soggysandwiches]

looking for some 95 brakes. i've got 130s i'd trade if anyone wants them

[b_Nutterbutter]

Ive got some 95's in pretty good condition id trade you for.

[jakezee]

Looking for some heel shims to get some Delta Force on my new Brahma 82's - anyone holding?

Bad idea?

[Eluder]

Bad idea?

Let me see if I can find a set I once had.

[jakezee]

Let me see if I can find a set I once had.

Appreciate that! These skis are a little demanding to get everything out of them, and I like that - just looking for a little help.

[jakezee]

I have these non GW pedestal/afd's from p18's and pair of 4mm and 1mm shimsAttachment 483035

AFD's sold to ASP.

Still have toe piece shims and pedestals - free with shipping

[SchralphMacchio]

Hoping to swap my extra 95mm brakes for some 115s. They are new.

Did you get this settled? Have 115 (used 1 season) need 95.

[Muggydude]

Anyone have 95mm brakes they’d sell?


Sent from my iPhone using TGR Forums

[AlpiNord]

FWIW & FTR, I measured the adjustment range for the heel forward pressure. It’s ‘about’ 12mm at an angle, but nets ~10mm laterally (fore and aft).






Sent from my iPad using TGR Forums

[AlpiNord]

I have an old pair of 115mm brakes for $15, shipped, posted on our store here:
https://www.slidewright.com/dp/Look-Pivot-Brakes-115mm/



A couple of the arms are wonky and need some ‘some love taps/bending and persuasion’ to get them rotating smoothly again.


Sent from my iPad using TGR Forums

[LT]

I have some complete 130 brakes I'm trying to get rid of. In Tahoe, let's make a deal.

[AlpiNord]

I forgot to measure Pivot heel screws during a recent mount. Can someone post measurements?

To provide screws for the above brakes, the KUU M5.5x14mm pan heads are a skootch long and may or may not need a touch of grinding. The 12mms might be a little short but ok. The rear heel screws shown are Snoli M5.5x28mm pan heads and require cutting/grinding.


Sent from my iPhone using TGR Forums

[waveshello]

PSA for the homies:

Finding the taller (20mm total length of screw) low head / pan head screws for the pivot heels is nigh impossible. If you are missing them and desperate, you can order the CAST screw hardware kit for $16--it includes 4 of those screws. The CAST kit uses those to secure the heel riser / brake retention piece, but they are identical to the longer pivot heel screws.

If someone has a better source, I'd love to hear about it.

Sent from my SM-G965U using Tapatalk

FYI. I think I posted measurements a while back, I'll check.

[waveshello]

L to R: Factory Pivot 20mm screw, CAST hardware pack 19mm screw, Slide Wright Pz #2 18mm screw.

The screws included in the CAST hardware kit for the break hold down / heel riser assembly are the closest replacement I've found for the long pivot heel screws.



As I was taking this pic I discovered that my work bench was energized... my old drill press was leaking voltage. Yikes, glad it was me that discovered it. It's probably been happening for a while but I happened to run out there with bare feet tonight [emoji51]

Sent from my SM-G965U using Tapatalk

FYI - sorry, no meaurements.

[waveshello]

I forgot to measure Pivot heel screws during a recent mount. Can someone post measurements?

To provide screws for the above brakes, the KUU M5.5x14mm pan heads are a skootch long and may or may not need a touch of grinding. The 12mms might be a little short but ok. The rear heel screws shown are Snoli M5.5x28mm pan heads and require cutting/grinding.


Sent from my iPhone using TGR Forums

Are your 28mm pan heads for sure the same thread pattern as a regular alpine threaded screw? I ran in to this issue with the ones skimo.co was selling a few years ago:

Another PSA for the homies: The 28mm pan-head screws (partially threaded, black in color) that could be found at skimo.co and look similar to 28mm pan-head screws offered elsewhere ARE NOT ALPINE 12AB THREADED. They have a different pitch and deeper threads. No doubt they will work fine in new holes, but you should not try to use those screws in existing holes--you will ruin the threads and risk a binding pullout.

Fortunately I caught this before I ruined any threads.

EDIT to say that the difference in pitch is significant, not slight/compatible like the differences between a M5.5/12AB/#12 screw.

[AlpiNord]

Are your 28mm pan heads for sure the same thread pattern as a regular alpine threaded screw? I ran in to this issue with the ones skimo.co was selling a few years ago:

Yes. These are from the Snoli & KUU 12AB thread/alpine screw options we've been providing for a long time.





If I had taken the measurements while I was mounting the Pivots the other day I could have confirmed sizing for recomendations and set up a kit and/or consider cutting a bunch of the 28mms to correct length.

[waveshello]

Right on, that's good news. I will get my calipers out and measure the screws this evening, happen to have some pivots sitting on the work bench at home.

[AlpiNord]

I reread the piece about the incorrect screws and started wondering. I checked them against an AB12 tap, threaded into heli-coil and compared to other screws and cannot see any difference in threads.

SVST clearly stated them as alpine M5.5 alpine screws (I'm measuring (6) threads in ~9.8mm on tap and screws):



Here's Snoli's page.

[TNThor]

I pulled some Look P18 toes and Rossignol P15 heels off a pair of 2012 Bent Chetlers (123 waist). Brakes measure in at 120mm. One toe is missing the AFD. Hit me with an offer if you need some pieces.

Sent from my SM-N970U using TGR Forums mobile app

[halliday]

Toes are 16mm
Turntable front are 10mm
Turntable rear are 20mm

For 15s and 18s

[charlesj]

Anybody have a spare toe window??