If you compare cost/link for whatever size chain, oftentimes you come out ahead buying loops over spools and the associated tools/labor.
http://www.baileysonline.com/Chainsaw-Chain/
If you compare cost/link for whatever size chain, oftentimes you come out ahead buying loops over spools and the associated tools/labor.
http://www.baileysonline.com/Chainsaw-Chain/
my buddy cut the big wood down on the coast for a bit until it freaked him out too much and he said the outfit he worked for issued each faller 3 chains every morning which they turned in every night to be machine sharpened and the fallers were not allowed to file chains
I got my system down pat to sharpen pretty quick using that Oregon jig and so I always have 2 sharp chains but i agree not everybody cares how sharp a chain is and given wages maybe a new chain makes sense?
I'm also pretty anal about my maintenance routine so after a day of running saw, I swap out the air filter ( I got 2) to be washed & dryed, clean sawdust out of engine, pull the cover to clean the smoo out of clutch area and sharpen chain.
Might seem excessive but no lost time so far
Lee Lau - xxx-er is the laziest Asian canuck I know
I don't think my jig would stand up to heavy use but its ok for once a week
http://www.baileysonline.com/Chainsa...hain-Grinders/
If it makes business sense electric chain grinders would be the tits but then you still got to pay someone to run it
So depending on circumstances it might be simpler for his saw guy to just replace the chains a lot
Lee Lau - xxx-er is the laziest Asian canuck I know
It doesn't make sense if everyone in the field is running dull, beat to shit chains that aren't sharp. Rock hits? Yeah, just get rid of them.
I run Ops for a ski area and we have switched to carbide chains because with how low shit has to get cut to the ground, you are going to hit rocks eventually. With how much wood we were running through, how often chains needed sharpening and the time it took- carbide is well worth it.
The cut may not be quite as fast as some of the more aggressive chippers out there but it cuts smooth and fast- and goes weeks without sharpening, not hours. Even if we threw them in the garbage rather than have them sharpened they’d still be worth it in productivity and man hours.
http://www.baileysonline.com/Chainsa...ain-3-8-X-050/
Obviuosly you have done the math but besides cutting "significantly slower" Carbide chains look pretty fucking expensive ?
Lee Lau - xxx-er is the laziest Asian canuck I know
Yeah it looks like throwing away money because you can’t sharpen chains.
I didn't believe in reincarnation when I was your age either.
i have had chains sharpened by grinders using a jig and the chain loses it's bite really quickly
^^ Are you talking carbide or regular?
"timberridge is terminally vapid" -- a fortune cookie in Yueyang
regular - too cheap to buy carbide
I can cut a lot of wood with a new regular chain. my friends that have it together touch the chain up with a round file. I am not very good at it
Gotcha. Some shops by me are better than others w/ that. Try another shop.
Depends what you cut too. In our area dogwood, locust and hornbeam can eat up a chain in 25 cuts. Maple and birch you can go for weeks. Oak is in the middle.
"timberridge is terminally vapid" -- a fortune cookie in Yueyang
i cut predominantly ash, some oak and maple
Remember there being a few posts on some affordable Alaskan mills, can’t seem to find it. Anyone have any recommendations? Have a Stihl MS 271 w/ a 20” Bar. Not looking to getting into anything super heavy duty, looking at something like this...thoughts?
https://www.amazon.com/Granberg-Chai.../dp/B000AMFY90
Sent from my iPhone using TGR Forums
Maybe the best IG post for this thread on this site. #bitchingraphicsdude. #powandsaws
https://www.instagram.com/p/Bfd4AfcjPJk/
Hmm, looks like that's it. I never saw (heh) that before. The first Megawatt I noticed was the blue.
Yeah I think that was the first year graphic. 2009-10 season almost certainly.
Wait a minute is it cool to like megawatts ?
Lee Lau - xxx-er is the laziest Asian canuck I know
I need a new saw for cutting trenches in snow to burry cable containments pipes. We have a deal with Husqvarna, and I'm a Stihl guy. I need a saw with a 20" bar, and has enough power to push through super compact snow.
If I was buying a Sthil I'd buy a MS440 with 20" bar. What is the Husqvarna equivalent?
Husqvarna 562. You'll love it... it's less displacement, but has gobs of power. Otherwise, the 372, if you can find one. The 562 is all you need.
Bookmarks