Printed it and lines up perfectly with my tectons.Quote:
Originally Posted by ~mikey b
I have a question that may be dumb, but to use this template, should I measure my BSL length from the Boot Toe line to the Heel line?
Printable View
Printed it and lines up perfectly with my tectons.Quote:
Originally Posted by ~mikey b
I have a question that may be dumb, but to use this template, should I measure my BSL length from the Boot Toe line to the Heel line?
Hi guys. Looking for the tyrolia template to mount my boys SX 4.5 AC. box says it’s the 94W jig. Toe and heel are square hole pattern. Having no luck with my search. Cheers
Sent from my iPhone using TGR Forums
You've probably figured it out by now, but the BSL measurement is usually written on the side of the boot's heel or under the instep, so you shouldn't need to measure it. Just match the number on the boot to the number in the template and you are golden. If in doubt, then just do a test mount on a piece of wood, a cardboard box or a piece of paper. The idea is to see if things line up, not test for retention - just mark a center line and a diagonal center mark, and see hot things line up.Quote:
Originally Posted by aguo5520
If the number is not there / worn away / not readable, then this list might provide the number: https://www.evo.com/guides/ski-boot-...gth-size-chart
marker Griffon template anyone? TIA
Should be “that” just don’t drill the 5th toe hole for late model demo plates.Quote:
Originally Posted by esseff
Sorry, my post wasn't clear. On the paper template (http://galibierdesign.com/images/oth...Vipec_Thom.pdf), there is a "Boot Toe" line and a "Heel" line. There's no BSL numbers on this paper template, so I'm wondering if all I have to do is match up my boot's toe to the boot toe line and match my boot's heel to the heel line, and just tape it together there.Quote:
Originally Posted by kid-kapow
Also wondering if after template is cut out and taped for the right BSL, the mount point should line up with the center of the boot, right?
just use the Vipec / Tecton template you find here.Quote:
Originally Posted by aguo5520
It is accurate (enough), contrary to what Thom states on his template.
His quoted differences of 0.25mm up front and 0.5mm in the back are not going to make any discernable difference, correct or not- drill bit slippage will probably account for the same/more - and when I measure the rear spacing 60mm seems bang on.
I've used Knut's template multiple times in the past and will use it again over the next few days for several pairs of skis.
Just do a test mount if unsure.
I've not used Thom's template, so I've got no advice on how to use it - sorry. I totally forgot about his alternative template when I read your post too :)
edit: the linked to template worked fine tonight.
Attachment 352601
I printed that template out and it doesn't line up with the holes very well, so I was pretty skeptical. But, it's good to know that you used it with success. I'll probably do a test mount and make sure it works.Quote:
Originally Posted by kid-kapow
as long as you print it 1/1 things should be fine, though keeping track of the bsl is never wrong.
Sure, you could foucs on tightening pair for pair wrt the holes, but then again I never did and it has turned out fine.
Yes, I just tested on my brand new STH2s and the heel pattern is too long. Anyone have an updated STH2 template? Surprised its this hard to find in 2020.Quote:
Originally Posted by tomelgato
I made my own STH2 template, modded from the knut version. Can’t remember why.Quote:
Originally Posted by KillerMonkey
https://drive.google.com/file/d/1_Rq...w?usp=drivesdk
Anyone know if there’s a template for kid’s Salomon Z 7’s? I’ve tried searching but couldn’t find anything.
Sent from my iPhone using TGR Forums
I have a new (never out of box) Marker MRR EPS3 Racing binding that I love (my 3rd one). If I read correctly do I just use the Jester binding template or is there a separate/distinct template for the MRR? Thanks in advance!
Print out a Jester template, place your MRRs on top, look carefully, report results.Quote:
Originally Posted by m4cecb
I was just handed down three pairs of marker junior 8 race bindings for my seven year old. He is currently set at din 2.5, and these bindings go from 2-8, which is quite higher than the .75-4.5 of his current kid bindings. I’m hoping to redrill some 118 Gotamas for him tonight as it should be a powder day tomorrow for him. These are junior bindings and his sole is 249mm. Can anyone steer me to a paper template for these bindings? Thanks
Never mind. After a couple of misalignments, I laid out some perfect holes for his boot size in some vinyl flooring. It’s super easy to clamp the homemade jig to a ski with a center line laid out on tape and punch the hole centers in. I’ve got a set of probably 20 center punches for various hole up to 3/8”. It’s been a very useful set of tools
Hi,
First post. I have tried for the last 2 days to search for the correct answer but I can't seem to find what I am looking for.
I have just purchased a 2020 set of Look Pivot 14 GW bindings for my wife and a 2021 set of Look Pivot 15 GW bindings for me. I haven't received the 15's yet so I can't measure or compare them. I will be mounting with inserts so I can swap bindings to different skis so I need to be extremely accurate.
Do these both use the same pattern? Has Look changed the pattern on newer Pivots? I have downloaded several Look "Pivot" templates and 2 were wrong and one seems to match the 14's. (I have double checked the scaling and measured the side rules to insure they are correct)
Can anyone point me to the most accurate templates or template for these?
I'm sorry if this has been posted previously. I have tried to search here and even TGR via Google but keep getting gateway timeouts.
Thanks!
P14 and P15 pattern are the same, and haven't changed in a long time. The labeling in the first post in this thread is a little funky but the FKS template (what the Rossignol branded Pivots were called, back when those were a thing) is the one you want. Ignore the holes labeled "Geze toe" and "Look toe" and use the four that are off the ski centerline. Do a practice mount in a 2x4 first to make sure you have it down.
Thanks! I will definitely do a practice run. That's the template that seemed correct. Thank you again for the help!Quote:
Originally Posted by HAB
Sent from my SM-G781U1 using Tapatalk
I'm mounting some pivot 15's and I can't for the life of me figure out which of the pivot templates discussed here I'm supposed to use. Anybody have a link to the pivot 15 template?
One too many beers. Someone answered this today. Damn the pivot world is above my paygrade :D
Look at Binding Freedom in the template section and in Alpine the Look Pivot/FKS is the file.Quote:
Originally Posted by AZskibum
https://docs.google.com/file/d/0B0Sn...NqOGJNcHc/edit
Just measure to make sure, after all I'm the guy with only a few posts and I'm figuring out the same thing lol.
Sent from my SM-G781U1 using Tapatalk
Does anyone have a paper template for the new Marker F12 Tour EPF bindings? The version on Binding Freedom is for the older and narrower version of the F12. Manual states to "ensure to use the paper drilling jig 6.2-1. Can't find it anywhere.
John
Apologies if I missed this but a quick search of this thread didn't yield what I was looking for. I'm sure it has been discussed somewhere...
Is there a good template out there for the Dynafit TLT Speedfit? It seems to be a Radical 1.0 toe but the heel is a different pattern from all other Dynafits. I've seen heel measurements that show the hole as 28W x 38.5L and that doesn't seem to match any of the Dynafit templates I've seen
I found this one from wild snow but it's a bit janky. I'm used to mounting with templates that have a clearer boot center line and I really like jondrums' with the nicks to help center the template on the ski. Can make do with this if necessary but given the limited adjustment range of this binding I'd love a slightly more confidence inspiring template
I'll be mounting a pair of these this weekend and wonder if someone can advise about setting the forward pressure. Is it like any other Marker Royal family binding (screw flush with end of housing)?
Also, any confirmed paper templates out there?
Having trouble finding the Marker Squire template. Got this off Slidewright (Jester/Griffon/Squire.) Does it look right for the Soul ID newer Squire version?
https://drive.google.com/drive/folde...yYY6Gg2a3Dd245
Royal Family(Jester/Griffon/Squire)has not changed....u r good to go. If it’s Terry’s template...100% confidence.
Sweet, that's what I was hoping. Thanks.Quote:
Originally Posted by BC.
hey - I have the binding freedom FKS/Pivot template.
Can anyone compare this to the actual jig?
I know the jig/manual has some fuckery where you're supposed to choke it 5mm shorter than wherever you boot sits in the jig, which is weird.
So does the template equate to the positions with boot in jig? or the positions AFTER you shorten the jig per the shop manual?
so fucking ambiguous. thanks
Any templates work with Marker Free Ten? Search bar didn’t help.
Sent from my iPhone using TGR Forums
Quote:
Originally Posted by slowroastin
Sent from my iPhone using TGR Forums
Im mounting a pair of Look SPX12 demo/rental. I have checked this massive thread but cant seem to find any template for them. I found something Rossi but that didn't work at all. The width between my holes are 33mm (give or take a few) both toe and heel. The distance between hole pairs are toe piece 92mm and heel 80mm. Anyone sitting on a template for this binding?
I'm guessing you looked at the Demo template I put up for the Axial 2? (It sounds like it's not even close.)
I'd be glad to help you create one.
It's not that hard.
You follow some steps to get measurements, and I'll crank the template. We might need 2-3 iterations before it's good, but it's really not that hard or even time-consuming.
Look here:Quote:
Originally Posted by slowroastin
https://drive.google.com/drive/folde...yYY6Gg2a3Dd245
Measured from a previous mount with said binding has 120 mm from toe piece rear holes to rec line, and 115 mm from heal piece front holes to rec line. 92 and 80 mm seems accurate. Holes closest to rec line, toe and heel plate 32 mm apart. Holes furthest from rec line 35 mm apart.
Caveat. Not confirmed 100% that this puts BC at rec line with binding set to corresponding boot size though.
Anyone mount kingpins with inserts? Anything special I need to know?
Only mounted Kingpins once. Extremely sensitive plastic in the heel plate. Be careful so you dont thread to far when adjusting forward pressure. But if you already have them mounted and just are changing the holes into inserts I dont see any problems there
Here we go again! Im mounting ATK Crest 10 (Hagan Pure 10 is the same binding branded for the american market). ATK are very generous and provide a paper template themselves. https://www.atkbindings.com/wp-conte...-crest8-10.pdf The problem is that the template is not made to mount according to boot center line and with a bsl-measurement to adapt. I find it extremely complicated to find a way to get the boot center properly and totally vertical down to the ski so therefore I prefer proper paper templates. Does anyone know of one?
Searched with no luck. Anyone have a template for Tyrolia SLR 7.5 AC junior binders? there is a demo plate involved. thanks!
Hi!Quote:
Originally Posted by Spyderjon
Could you make a pdf template for Marker Duke PT and BSL 305 mm?
I couldnt write a private message, my email - vk51 a yandex dot ru
Thanks a lot.