FS: FKS/Pivot Bindings: Used complete sets, and parts, mix-and-match

Quote:

---

Originally Posted by Bosco

Although a post stated this cannot be done, I just did it yesterday, but there are some caveats. The replacement AFD's appear to be designed for the dual WTR/DIN bindings as the interface has a circular button to replace the dual mode WTR/Alpine screw (old pivots had a rectangular interface). This seems weird since data shows that the dual mode bindings support gripwalk in the alpine mode. However, I replaced the new gripwalk AFD's for an old set of pivots with the rectangular interface and it seems fine (all measurements are the same across the different interfaces) except for a small gap between the binding and AFD.

I do have an extra set of the gripwalk AFD's that I may par with.

---

The new GW compatible P12s/14s still have that hole for the screw on the dual Alpine/WTR AFD, so the GW AFD physically fits on the Dual toe, but the toe wings are different so you end up with a giant gap between the boot sole and the AFD if you do that swap. I tried to make it work, but it doesn't.

Interesting that they seem to work on the older toes though — I remembered the shape of the AFD being pretty different where it interfaces with the rest of the toe so I'd assumed that wouldn't work either. But I haven't tried that one.

Here are some pictures:

Old vs. gripwalk AFD:
Attachment 398822

A picture with an old pivot toe mated to a gripwalk AFD. the housing sits on top of the button and the lip of the white plastic of the AFD.
Attachment 398823

Quote:

---

Originally Posted by Dee Hubbs

Yes they should be the same, the outlier is the "Race" model that has the rear heel holes further back.

---

Cool, thanks again DH. Found a cheap pair for a buddies youngster. I have the jiga rex plates for look so i can mount them for him

Sent from my SM-G950W using TGR Forums mobile app

Pivot 15 GW afd. Pulled after a few days use. Have the screws for toes also


Sent from my iPhone using TGR Forums

Quote:

---

Originally Posted by whyturn

Pivot 15 GW afd. Pulled after a few days use. Have the screws for toes also


Sent from my iPhone using TGR Forums

---

I’ll take those. Pmd

Looking for Pivot 18 Alpine AFDs with 4mm+1mm toe shims (could do this separately if you don't have both). I have a pair of GripWalk AFDs that I would rather keep, but I could do a trade if necessary.

Quote:

---

Originally Posted by Powdurr

Looking for Pivot 18 Alpine AFDs with 4mm+1mm toe shims (could do this separately if you don't have both). I have a pair of GripWalk AFDs that I would rather keep, but I could do a trade if necessary.

---

Why are you looking for the alpine + shims? GW afd gives you the same height.
I’ve got a bunch of shims I can send tho

I’ve got the alpine afds, only the plastic bit though that goes around the metal plate


Sent from my iPhone using TGR Forums

Quote:

---

Originally Posted by mr_pretzel

Why are you looking for the alpine + shims? GW afd gives you the same height.
I’ve got a bunch of shims I can send tho

---

Yeah it gives a similar height but for my Alpine (non-GW) boots the connection seems better on the Alpine AFD.

PMd about the shims.

Catch and release. Pivot 12, 115 brake, black, great condition. Would like to get 130 + shipping.

Attachment 400964

Edit:pending.

Brand New pivot 18 gw toes Forza 2.0 for sale pm me with offers
Attachment 401068

130 Shipped CONUS


And
Soldd 125$

Quote:

---

Originally Posted by mellowk

Brand New pivot 18 gw toes Forza 2.0 for sale pm me with offers
Attachment 401068

---

List a price please

seeking heels only, 14/15/18 din

thanks

anyone have a new(ish) pair to unload, any din, 95-100mm brakes?

also i have a pair of black matte p18's 105mm brakes from 2006.. but the heels are super stiff and there's some play in them. push boot down and they don't snap up, just goes up about halfway.. there's a lot of friction, have to pull them up by hand. probably something that can be fixed if you take them apart and grease or what not.. but not something i'm going to fuck with

Quote:

---

Originally Posted by grapedrink

anyone have a new(ish) pair to unload, any din, 95-100mm brakes?

also i have a pair of black matte p18's 105mm brakes from 2006.. but the heels are super stiff and there's some play in them. push boot down and they don't snap up, just goes up about halfway.. there's a lot of friction, have to pull them up by hand. probably something that can be fixed if you take them apart and grease or what not.. but not something i'm going to fuck with

---

How much for your P18s?

Quote:

---

Originally Posted by nbak

How much for your P18s?

---

not sure what they're worth

Attachment 401291
Attachment 401294

Want 115mm p18 brakes

Willing to trade bnib forza look p18s 130mm brake for equivalent p18 115mm.

Or trade brakes 130 for 115

Tyx

Sent from my SM-G998U using Tapatalk

skini,

I've got a decent condition set of 115 brakes on my 12's and need some 130's by mid next week. If you think you could get them here in time I'd trade those for yours - each cover shipping. I could even throw in $10 for a sixer for ya. PM me if interested

LT

Quote:

---

Originally Posted by Lord Thomas

skini,

I've got a decent condition set of 115 brakes on my 12's and need some 130's by mid next week. If you think you could get them here in time I'd trade those for yours - each cover shipping. I could even throw in $10 for a sixer for ya. PM me if interested

LT

---

Pmed. Let's make it happen. I might need quick instruction as to how to remove the 130 brakes.

Sent from my SM-G998U using Tapatalk

To remove:

Use two hands to transition the dildo to the up position, watch your fingers. Use a pozidriver to unscrew the adjustment tubes a few turns at a time, alternating sides until the brake assembly separates from the dildo.

Reinstall is the opposite, but must be done carefully to avoid cross-threading.

Quote:

---

Originally Posted by grapedrink

not sure what they're worth

Attachment 401291
Attachment 401294

---

How much are they worth to you? I'm curious about fixing the heels.

Quote:

---

Originally Posted by jackattack

To remove:

Use two hands to transition the dildo to the up position, watch your fingers. Use a pozidriver to unscrew the adjustment tubes a few turns at a time, alternating sides until the brake assembly separates from the dildo.

Reinstall is the opposite, but must be done carefully to avoid cross-threading.

---

Thank you. That seems to be the easier way compared to popping the bottom plate and disassembling.

Sent from my SM-G998U using Tapatalk

Pretty sure you cannot pop the bottom plate and disassemble….every time I’ve purchased they’ve come with like the above


Sent from my iPhone using TGR Forums

Quote:

---

Originally Posted by detrusor

Pretty sure you cannot pop the bottom plate and disassemble….every time I’ve purchased they’ve come with like the above


Sent from my iPhone using TGR Forums

---

You can. It's not hard, but it can be a little tedious putting it all back together.

https://vimeo.com/4218404

Sent from my SM-G965U using Tapatalk

Quote:

---

Originally Posted by waveshello

You can. It's not hard, but it can be a little tedious putting it all back together.

https://vimeo.com/4218404

Sent from my SM-G965U using Tapatalk

---

@detrusor never believes a word I say. Once my teacher always my teacher. [emoji1787]

Sent from my SM-G998U using Tapatalk