Printable View
Grinch, sorry to be away so long, the snow has been great here.Quote:
Originally Posted by grinch
191 length, stiff flex. They were just under ten pounds for the pair; mounted with CAST plates and sth16’s. I’ve got a few days on them now, I’ll bump the Lithic thread shortly with some details for the collective. The short story is that I’m very happy.
Sent from my iPhone using TGR Forums
Ya I see that. Nice pics.Quote:
Originally Posted by riff
Lots of options with those cohens. Width and length and the protest like design. I’ll stay tuned to the mythic thread. Should be relatively ez to figure weights of a shorter model from yours being similar construction
Alright, so I didn’t mount my skis as this thread says.
I pulled my bindings off to put in BF inserts and noticed that 2 of the 4 binding holes for the heel piece on my skies are basically touching the plugs that were used to fill the holes from the previous mount.
Attachment 261973
Attachment 261974
If I try and do the BF inserts the edge of the insert will basically be in the middle of the plug. Which doesn’t seem safe to me.
What do you guys think? This was the third mount on these skis. Are they salvageable?
Sent from my iPhone using TGR Forums
Yes. Drill and pull out plugs. Pound in hard wood plugs with epoxy, chisel flush the next day and finally mount however you want.
Bingo. Feel like this should be a pinned response in this thread.Quote:
Originally Posted by roverdoc
Sent from my iPhone using TGR Forums
... and if you want to get fancy you can slightly countersink after chiseling and cover top of dowel with epoxy to waterproof the core and even more fancy you can add pigment to the epoxy to color match your skis....however very difficult to match red skis ;)
Awesome. Thanks for the help. So drill the old plugs, pound in wood plugs with epoxy, chisel a day later, countersink and cover with epoxy to waterproof. Once that’s done drill the BF holes at the current mounting holes.Quote:
Originally Posted by roverdoc
Idk about the coloring though, if it looks too good people may start to think I am actually decent at skiing haha.
Sent from my iPhone using TGR Forums
Haha. I bought a bag of tognar plugs which are nice and already cut down but if you want to save a few bucks bamboo chopsticks etc etc have been mentioned. I eclipsed some holes on my wife moments and the mount into the plugs felt more solid than the original core. no way they are ripping out.
May have to grab some of the tognar plugs then. Was planning to run up to Home Depot and grab a dowel then pound it in. They are only like $0.75Quote:
Originally Posted by roverdoc
Sent from my iPhone using TGR Forums
I use blunted wood golf tees for hole plugs. Dremel them off, and you can use them again. Super cheap.
I dab some touch up paint on the surface of the wood plug to seal them - seems to work fine. I use some old automotive touch up paint left over from a car I no longer own.
Quote:
Originally Posted by powderdetective
Golf tees can often be really soft and made from pressed wood dust. Hardwood dowels form home depot would be your best bet.Quote:
Originally Posted by El Chupacabra
The binding screw shank is 4.1 mm and the thread width is 5.4mm. I've had good results using 5/32 (3.9688mm) hard wood dowels.
Margotrons method is perfectly overkillQuote:
Originally Posted by powderdetective
Quote:
Originally Posted by margotron
Sounds like a solid method. On the topic of epoxy, should I have orange hardmann or JB Weld. Is one better than the other for this?Quote:
Originally Posted by tuco
Sent from my iPhone using TGR Forums
I don't really have a dawg in this fight cuz the FKS is not even on my radar but I was looking at HOW CLOSE together the screws are on the heel of an FKS compared to the spacing on the other brands and wondered if maybe that is why they pull out??Quote:
Originally Posted by Dee Hubbs
For sure, the close mounting pattern has some negatives, and the short mounting point has some positives.Quote:
Originally Posted by XXX-er
My above points were trying to highlight some pointers on how to reduce the risk of mounting mistakes that lead to pull out.
Yeah so IME its always good in tech discussions to give valid reasons for your POV
SO you might have said to buddy
"hey you stupid cunt this is why you shouldn't move the Heel piece "
and then assuming you are Canadian you will be moved to apologize
some thing along the lines of " I'm sorry you are a stupid cunt "
orange hardmann epoxy and or any slow set marine epoxy would be preferred.
Quote:
Originally Posted by powderdetective
G flex
Sent from my iPhone using TGR Forums
I haven't done this with many epoxies, but after finishing a job, I spread out the remaining Gflex into a thin film on the piece of cardboard I mixed it on.
After a 24 hour cure, I was amazed at how much I could flex it with no signs of cracking.
... Thom
Another G Flex fan here, I switched to it five or so years ago, amazing stuff
G flex and hardman are both great stuff. I use hardman because it comes in individual packets, so I don’t have to worry about wasting a larger quantity of g flex because I use it very infrequently. I just try to do a bunch of jobs that require epoxy at the same time. If I was still in the shop, g flex is more convenient because you can mix exactly the quantity you need for each job.
those are amazing.
what size are those, as well as your other RXs?
Another mounting session in the garage. This time mounting my lady friends new touring setup.Attachment 262228
Bindings came off her 170 Volkl Kikus, which were a little to much ski for her. The sin7 should be much better for her on both the up and down.
Attachment 262229
I even got her skins re-cut and trimmed. Ready to go. Speaking of, a minor rant but not a big fan of the Black Diamond tip loop that uses the three tiny screws instead of the old fold back.
https://media.makeameme.org/created/...ful-should.jpgQuote:
Originally Posted by flowing alpy
Happy 2019